Top Tips On Brake Repairs
Before you start work, make sure you have a good repair manual. We recommend an online manual from
our car manual section for step-by-step instructions on changing your brakes. You can even find out things only the dealer knows about your vehicle..
Your car's brake system is a complex grouping of parts which serve a critical role in keeping you safe. No other system in the car is as important for your safety. Keeping your brake system in tip-top shape should be your top priority.
Let's start with the pedal and work our way down the braking system to better understand how it works. The Pedal is a strong steel lever which transmits the force from your foot to the master cylinder. The pedal typically has a switch attached to it, to turn on your brake lights when you press the pedal down.
When you push down on the pedal, the master cylinder is pushed via a push rod. The master cylinder consists of a piston and a fluid
reservoir. When the piston is moved, it pushes the brake fluid through the brake lines and into the caliper or wheel cylinder.
Most all cars have disc brakes on the front wheels, and many have disc brakes on the rear also. When disc brakes are not used on the rear, drum brakes are used. The fluid being pushed from the master cylinder through the brake lines pushes a piston in the brake caliper. This in turn applies force to the brake pads.
The brake pads are typically made from a hard organic or metallic compound. The pads are made to survive under high heat and pressure. When the brake pads contact the rotor, there is friction and heat is created. This is how your car stops, by turning the rotating energy of your wheels into heat through friction.
The last part of your braking system is the rotors. Typically made from cast iron and made heavy enough to dissipate heat and not warp over time.
Unfortunately, in today's cars, many of the rotors are not large enough, and can warp within a few 1,000 miles. The rotor is bolted between the wheel and the spindle, and rotates at the same speed as the wheels.
Common Problems
Wear: The braking system does a lot of work and the brake
pads take the brunt of the punishment. It is a good idea to have you brake
pads checked every 6 months or when you suspect a problem. Symptoms
include squeaking, grinding, or increased stopping distance. Most pads
have a thin metal tab which vibrates against the rotor when the pads wears down
to a dangerous level. Some pads do not have this and if not checked
periodically can wear down far enough to ruin the rotors. A modern trend
is to make the brake pads very hard thus extending life. This harder
material can squeak and sound like the wear indicators. Brake dust can
also cause squealing but can be fixed by spraying brake cleaner on the brake
system to remove the dust.
Warped Rotors: More common in newer cars, but possible on
all disc brake systems. Rotors warp due to being overheated or incorrect
tightening of the wheel. A warped rotor will give a pulsing feeling when
applying the brakes. This pulsing can be annoying and dangerous.
Most newer cars have rotors which are very thin and warp very easy.
Furthering the problem, the manufacturer does not leave enough material to
resurface the rotor. Check with you mechanic to make sure you can safely
have the rotors machined or replace with new rotors. To resurface, the
rotor is placed in a lathe and a cutting tool removes a few thousandth's of
material from the braking surface. This restores the flatness of the rotor
and eliminates the pulsing sensation in the pedal. Make sure when your
mechanic puts everything back together that he torques the lug nuts to proper
specifications and never uses an impact wrench. If the lug nuts are
not tightened evenly the rotor can warp and you are back to square one.
Note: Some shops use a torque stick, which attaches to an impact wrench
and does not allow the torque wrench to tighten more than it should. This
is acceptable. If your mechanic does not use a torque wrench or torque
sticks, find another mechanic.
Preventive Maintenance
- Avoid "riding" your brakes. It's better to slow down with
moderate pressure and then releasing the brake to cool, than riding the
brakes and overheating them
- On steep grades consider downshifting to save your brakes. Only do
this when traction conditions are good. In ice, snow, or even rain,
downshifting into too low of a gear may cause a skid. Downshifting
lets you engine do some of the braking instead of your brakes.
- Keep your wheels and braking system clean. Clean brakes work better
and keep temperatures down. Use a good wheel cleaner which you know if
safe for your wheel finish.
What To Discuss With Your Mechanic
- Be weary of low priced brake jobs advertised in the paper or TV.
Some shops will try a bait and switch or find other parts which
"need" to be replaced. Salesmen will try to make you feel
guilty for putting your families safety on the line. They claim you
need the premium pads and rotors, of course at a higher price.
- You mechanic should clean all the components of the brake system to ensure
a dust and squeak free job.
- All bolts including lug nuts should have anti-seize compound on the
threads to prevent them from rusting fast and causing headaches down the
road.
- Have your mechanic use an anti-squeak compound on the back of the brake
pads. This keeps the pads from vibrating and annoying you to no end.
There are spray, and paste forms, with the paste working better for me.
- Insist on seeing the pads they removed from your car. There is no
use paying to replace something that doesn't need to be replaced.
- National brake shops are not all bad. Some stores only do brakes so
they should be pretty good at it. Ask around and get recommendations
before you get work done. Quality depends on the owner of the national
chain store, not the parent company so shop carefully.
- Do you need the lifetime brake pads? Well that depends on how long
you will keep the car and how many rotors you plan on buying in the next few
years. This initial cost is a little higher due to the fact the
manufacturer knows he will most likely have to give you another set when
yours wear out. Also these pads are made from a harder material and
tend to wear down the rotors instead of themselves. You would be
better off buying the basic pads and replacing them periodically instead of
costly rotors every year or two.
- Make sure your mechanic uses a torque wrench or torque sticks on their
impact guns. See above for the explanation.
Safety is important to you and your family. Stay safe by
educating yourself and not by falling pray to the salesman. When you think
you have a brake problem, take it to be checked by a mechanic you trust, for
your families sake.
|
|
